This is an old revision of the document!
Table of Contents
Definition of "Hacker"
For the purpose of this article, the term “hacker” 1) refers to automated systems which attempt to login to your Synchronet TCP/IP servers and services using common, well-known, or randomly selected credentials (user names and passwords). These “hackers” are usually not humans sitting at keyboards, typing names and passwords, but rather automated systems (e.g. scripts, a.k.a “robots”) which scan the Internet looking for systems with user accounts with guessable credentials and/or known vulnerabilities in their system software. Sort of like a modern version of “War Dialing”.
The truth is, if one of these scripts successfully logged into your BBS as “root” or “admin” or whatever, they wouldn't know what to do: These scripts are most likely expecting to encounter some kind of Unix shell prompt with which they can further interrogate the system for known vulnerabilities or use the system to launch attacks against other hosts on your local network or the Internet. A Synchronet BBS command shell would not provide a favorable environment to these “hacking” scripts, but they don't know that, so they will just continue to blindly probe your ports and rattle your doorknobs. It may be irritating to some, but it's mostly harmless.
Denial of Service
One thing these attacks can do, though it's usually not their intention, is to tie up your BBS's resources (e.g. Terminal Server nodes for Telnet, RLogin, SSH connections and logins). If you find that your Terminal Server's nodes all are being occupied by “hackers” attempting brute-force logins (or just sitting stupidly idle until disconnected due to inactivity), you can mitigate this problem by setting the
MaxConcurrentConnections value in the
[BBS] section of your
ctrl/sbbs.ini file to a non-zero value which is fewer than the number of BBS nodes you have setup in SCFG.
For example, if you have 4 nodes configured in SCFG, then you might want to limit the maximum concurrent connections (from the same client IP address) to 2 (e.g.
MaxConcurrentConnections=2). IP addresses listed in your
ctrl/ipfilter_exempt.cfg file are not connection-limited. Clients that are successfully logged into your BBS do not count against the concurrent-connections limit, if one is configured.
This protection mechanism was introduced in Synchronet v3.17 (November, 2016).
Synchronet normally disallows the use of common passwords by users (see the
text/password.can file) and system operator accounts are protected with a secondary “system password”, so there should be little chance of a dictionary-based login attack actually succeeding. You can run
exec/badpasswords.js (e.g. using jsexec) to check your user database for common passwords if you wish.
To protect against “brute force” style attacks, that is, where an attacker may iterate through every possible password for a given user, Synchronet:
- Will delay a configurable amount of time before responding to failed login attempts (default: 5 seconds, see LoginAttemptDelay)
- Will throttle TCP/IP connections from attackers, increasing the configurable delay with each login failure (default: 1 second per failure, see LoginAttemptThrottle)
- Limit the number of concurrent connections to the Terminal Server from a common host/client IP address (default: disabled, see MaxConcurrentConnections)
To do this, Synchronet tracks the source IP address of all failed login attempts. The sysop can list the failed login attempts:
- In the Synchronet Control Panel for Windows, using the View->Login Attempts... menu option
- In the Synchronet Console (sbbs), using the
a(show failed login attempts) command
- These IP addresses are only tracked during a single continuous invocation of the Synchronet process (rerunning the BBS clears the list and resets any temporary bans in effect)
- Consecutive failed login attempts with the same credentials (name and password) are counted as a single failed login attempt
- When a client successfully authenticates, its IP address is removed from the failed login list (if it exists there)
To temporarily ban future connections from an IP address that performed multiple consecutive failed login attempts:
- In the Synchronet Control Panel for Windows, set File->Properties->Security->Failed Login Attempts->Temp Ban Threshold value and Temp Ban Duration...
... to numbers you are comfortable with.
The default temporary ban Threshold is 20 (failed login attempts) while the default temporary ban duration is 10 minutes.
Note: Setting the Temp Ban Threshold to 0 will disable temporary bans based on failed login attempt counters, but a failed login with a blocked name (from
text/name.can) will still result in an immediate temporary ban, regardless of the Temp Ban Threshold value.
To permanently block future connections from an IP address that has performed multiple consecutive failed login attempts:
- In the Synchronet Control Panel for Windows, set File->Properties->Security->Failed Login Attempts->Perm Filter Threshold value... (used to be called “IP Filter Threshold”)
... to a number you are comfortable with. I do not suggest setting this value lower than 10 so that you do not filter the IP address of valid BBS users who simply forgot their password. You may wish to warn your BBS users that they should not repeatedly attempt invalid passwords or their IP address may be automatically blocked by your system.
The default Filter Threshold value is 0 (disabled).
LoginAttempt values may be set in your
sbbs.ini to different values for each Synchronet server/service if you wish, but that's a configuration that most sysops won't need.
sbbs.ini for a list of all the failed-login-attempt related configuration settings available.